Step 1. Power off your iPhone 6S before beginning disassembly. Remove the two 3.4 mm Pentalobe screws surrounding the Lightning connector.

 LCDONE iPhone 6S LCD Screen Replacement Installation 1

Step 2. If you don’t have aniSclack, use a single suction cup to lift the front panel:Press a suction cup onto the screen, just above the home button. Be sure the cup is pressed securely onto the screen to get a tight seal.

 LCDONE iPhone 6S LCD Screen Replacement Installation 2

Step 3. There is a notch on the underside of the display just above the headphone jack that is the safest place to begin prying the phone open. Pull up on the suction cup to slightly separate the front panel assembly from the rear case. Take your time and apply firm, constant force. The display assembly is a much tighter fit than most devices and is held down with adhesive. Once a small gap has been opened, insert the flat end of a spudger above the headphone jack.

 LCDONE iPhone 6S LCD Screen Replacement Installation 3

Step 4. Twist the spudger to open the gap more and break it free from the adhesive. Keep pulling up on the suction cup while twisting the spudger.

 LCDONE iPhone 6S LCD Screen Replacement Installation 4

Step 5. Use the edge of a spudger to slice through the adhesive on either side of the phone.

 LCDONE iPhone 6S LCD Screen Replacement Installation 5

Step 6. Use the edge of a spudger to slice through the adhesive on either side of the phone.

 LCDONE iPhone 6S LCD Screen Replacement Installation 6

Step 7. Use the suction cup to open the display, breaking the last of the adhesive. Don’t open the display more than 90 degrees, as it is still connected at the top by three cables that may break if stretched.

 LCDONE iPhone 6S LCD Screen Replacement Installation 7

Step 8. Lean the display against something to keep it propped up while you’re working on the phone.

 LCDONE iPhone 6S LCD Screen Replacement Installation 8

Step 9. Remove the following screws from the battery connector bracket:

 LCDONE iPhone 6S LCD Screen Replacement Installation 9

Step 10. Remove the metal battery connector bracket from the iPhone.

 LCDONE iPhone 6S LCD Screen Replacement Installation 10

Step 11. Use the flat end of a spudger to disconnect the battery connector from the logic board. Push the connector to the side to ensure it doesn’t accidentally make contact and power on the phone while you’re working on it.

 LCDONE iPhone 6S LCD Screen Replacement Installation 11

Step 12. While holding the front panel open at about a 90o angle, remove the following screws securing the front panel assembly cable bracket: Three 1.3 mm Phillips #00 screws One 3.0 mm Phillips #00 screw Don’t lose track of this screw! It’s very important that the one 3.0 mm screw goes in the top-right corner of the plate. Anywhere else may cause damage to the logic board.

 LCDONE iPhone 6S LCD Screen Replacement Installation 12

Step 13. Remove the front panel assembly cable bracket from the logic board.

 LCDONE iPhone 6S LCD Screen Replacement Installation 13

Step 14. In the next three steps, take care to pry uponlyon the cable connectors, and not on their sockets on the logic board. Use the flat end of a spudger to disconnect the front-facing camera and sensor cable connector.

 LCDONE iPhone 6S LCD Screen Replacement Installation 14

Step 15. Use the flat end of a spudger to disconnect the display data cable connector. When reassembling your phone, the display data cable may pop off its connector. This can result in white lines or a blank screen when powering your phone back on. If that happens, simply reconnect the cable and power cycle your phone. The best way to power cycle your phone is todisconnect and reconnect the battery connector.

 LCDONE iPhone 6S LCD Screen Replacement Installation 15

Step 16. Finally, use the flat end of a spudger to disconnect the digitizer cable connector.

 LCDONE iPhone 6S LCD Screen Replacement Installation 16

Step 17. Remove the display assembly from the rear case.

 LCDONE iPhone 6S LCD Screen Replacement Installation 17

Leave a Reply